Selasa, 15 Januari 2013

Konfigurasi OSPF pada Cisco Packet Tracer



Pada kali ini saya menggunakan tiga Router ,tiga Switch dan tiga PC,
Dan Pertama kita desain seperti gambar dibawah!!!


Setelah Itu kita setting / pemberian IP Address di masing - masing client,
Gambar di bawah merupakan pemberian IP Address pada Client / PC0



Pemberian IP Address pada Client / PC 1



Pemberian IP Address pada Client / PC 2




Pemberian IP Address Router 0 :

 
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.7.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.20.11.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit


 Konfigurasi OSPF Router 0 :


Router(config)#router ospf 4
Router(config)#router-id 1.1.1.1
Router(config-router)#net 192.168.7.0 0.0.0.255 area 0
Router(config-router)#net 172.20.11.0 0.0.255.255 area 0
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



 Pemberian IP Address Router 1 :


Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.14.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.20.11.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 10.10.6.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit 


 Konfigurasi OSPF Router 1 :


Router(config)#router ospf 4
Router(config-router)#net 192.168.14.0 0.0.0.255 area 0
Router(config-router)#net 172.20.11.0 0.0.255.255 area 0
Router(config-router)#net 10.10.6.0 0.255.255.255 area 1
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Pemberian IP Address Router 2 :

 
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.21.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 10.10.6.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit


 Konfigurasi OSPF Router 2 :


Router(config)#router ospf 4
Router(config)#router-id 2.2.2.2
Router(config-router)#net 192.168.21.0 0.0.0.255 area 1
Router(config-router)#net 10.10.6.0 0.255.255.255 area 1
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#




Setelah dikonfigurasi selesai, coba di ping dari PC0 ke PC1 atau PC2 dan Sebaliknya.....
Apabila kurang dipahami bisa ditanyakan.....



SELAMAT MENCOBA.....

Tidak ada komentar:

Posting Komentar