Konfigurasi EIGRP pada Cisco Packet Tracer

Langkah Awal,
sebuah jaringan di bawah ini yang kita buat untuk konfigurasi EIGRP...

Langkah Kedua,
Pemberikan IP Address pada setiap PC yang terhubung..

  - Pemberian IP pada PC 0,

 

- Pemberian IP pada PC 0,

 

  

 - Pemberian IP pada PC 2,

 

Langkah Ketiga,
Selanjutnya pemberikan IP Address dan Konfigurasi EIGRP pada setiap router...
Contoh sebagai berikut : 

Pemberian IP Address Router X,

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.1.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Konfigurasi EIGRP Router X,


Router(config)#router eigrp 8
Router(config-router)#net 192.168.1.1
Router(config-router)#net 172.16.11.1
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

 

Pemberian IP Address Router Y,

  --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.5.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.1.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 18.10.10.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit 

Konfigurasi EIGRP Router Y,


Router(config)#router eigrp 8
Router(config-router)#net 192.168.5.1
Router(config-router)#net 172.16.1.2
Router(config-router)#net 18.10.10.1
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Pemberian IP Address Router Z,

 

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.8.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 18.10.11.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit


Konfigurasi EIGRP Router Z,


Router(config)#router eigrp 8
Router(config-router)#net 192.168.8.1
Router(config-router)#net 18.10.10.2
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

Setelah selesai semua nya, coba di ping dari PC0 ke PC1 dan PC2 atau sebaliknya, jika berhasil maka konfigurasi anda SUKSES..

SELAMAT MECOBA............