Selasa, 15 Januari 2013

Konfigurasi OSPF pada Cisco Packet Tracer



Pada kali ini saya menggunakan tiga Router ,tiga Switch dan tiga PC,
Dan Pertama kita desain seperti gambar dibawah!!!


Setelah Itu kita setting / pemberian IP Address di masing - masing client,
Gambar di bawah merupakan pemberian IP Address pada Client / PC0



Pemberian IP Address pada Client / PC 1



Pemberian IP Address pada Client / PC 2




Pemberian IP Address Router 0 :

 
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.7.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.20.11.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit


 Konfigurasi OSPF Router 0 :


Router(config)#router ospf 4
Router(config)#router-id 1.1.1.1
Router(config-router)#net 192.168.7.0 0.0.0.255 area 0
Router(config-router)#net 172.20.11.0 0.0.255.255 area 0
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



 Pemberian IP Address Router 1 :


Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.14.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.20.11.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 10.10.6.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit 


 Konfigurasi OSPF Router 1 :


Router(config)#router ospf 4
Router(config-router)#net 192.168.14.0 0.0.0.255 area 0
Router(config-router)#net 172.20.11.0 0.0.255.255 area 0
Router(config-router)#net 10.10.6.0 0.255.255.255 area 1
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Pemberian IP Address Router 2 :

 
Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.21.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 10.10.6.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit


 Konfigurasi OSPF Router 2 :


Router(config)#router ospf 4
Router(config)#router-id 2.2.2.2
Router(config-router)#net 192.168.21.0 0.0.0.255 area 1
Router(config-router)#net 10.10.6.0 0.255.255.255 area 1
Router(config-router)#log-adjacency
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#




Setelah dikonfigurasi selesai, coba di ping dari PC0 ke PC1 atau PC2 dan Sebaliknya.....
Apabila kurang dipahami bisa ditanyakan.....



SELAMAT MENCOBA.....

Konfigurasi EIGRP pada Cisco Packet Tracer

Langkah Awal,
sebuah jaringan di bawah ini yang kita buat untuk konfigurasi EIGRP...


Langkah Kedua,
Pemberikan IP Address pada setiap PC yang terhubung..

  - Pemberian IP pada PC 0,
 




- Pemberian IP pada PC 0,
 

  

 - Pemberian IP pada PC 2,
 

Langkah Ketiga,
Selanjutnya pemberikan IP Address dan Konfigurasi EIGRP pada setiap router...
Contoh sebagai berikut : 

Pemberian IP Address Router X,

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.1.1 255.255.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Konfigurasi EIGRP Router X,



Router(config)#router eigrp 8
Router(config-router)#net 192.168.1.1
Router(config-router)#net 172.16.11.1
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#

 
Pemberian IP Address Router Y,


  --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.5.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.1.2 255.255.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 18.10.10.1 255.0.0.0
Router(config-if)#band 125
Router(config-if)#cl ra 125000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit 


Konfigurasi EIGRP Router Y,


Router(config)#router eigrp 8
Router(config-router)#net 192.168.5.1
Router(config-router)#net 172.16.1.2
Router(config-router)#net 18.10.10.1
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



Pemberian IP Address Router Z,

 
     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.8.1 255.255.255.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 18.10.11.2 255.0.0.0
Router(config-if)#band 125
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit


Konfigurasi EIGRP Router Z,


Router(config)#router eigrp 8
Router(config-router)#net 192.168.8.1
Router(config-router)#net 18.10.10.2
Router(config-router)#end
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



Setelah selesai semua nya, coba di ping dari PC0 ke PC1 dan PC2 atau sebaliknya, jika berhasil maka konfigurasi anda SUKSES..



SELAMAT MECOBA............





Konfigurasi RIP pada Cisco Packet Tracer


Sebelum kita memulai konfigurasi,
Pertama kita buat sebuah jaringan sederhana...
seperti yang ada di bawah ini...



Kedua Pemberian IP Address pada masing-masing PC yang terhubung..


Pemberian IP address pada 'PC0'
 


Pemberian IP address pada 'PC1'






 Pemberian IP address pada 'PC2'



Pemberian IP address di Router0

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 20.20.20.1 255.0.0.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.20.1 255.255.0.0
Router(config-if)#band 64
Router(config-if)#cl ra 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Konfigurasi RIP di Router0


Router(config)#router eigrp 9
Router(config-router)#net 20.20.20.1
Router(config-router)#net 172.16.20.1
 Router(config-router)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#


Pemberian IP address di Router1


  --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 30.30.30.1 255.0.0.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 172.16.20.2 255.255.0.0
Router(config-if)#band 64
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit

Router(config-if)#exit
Router(config)#int se3/0
Router(config-if)#ip add 192.168.20.1 255.255.255.0
Router(config-if)#band 64
Router(config-if)#cl ra 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit 


Konfigurasi RIP di Router1
Router(config)#router eigrp 9
Router(config-router)#net 30.30.30.1
Router(config-router)#net 172.16.20.2
Router(config-router)#net 192.168.20.1
Router(config-router)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#




Pemberian IP address di Router2 
 

     --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 40.40.40.1 255.0.0.0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.20.2 255.255.255.0
Router(config-if)#band 64
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit




Konfigurasi RIP di Router0

Router(config)#router eigrp 9
Router(config-router)#net 40.40.40.1
Router(config-router)#net 192.168.20.2
Router(config-router)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
wr
Building configuration...
[OK]
Router#



Setelah dikonfigurasi, coba di ping dari PC0 ke PC1 atau PC2 dan sebaliknya...


SILAHKAN MENCOBA...